本文圖片、文字由上海淞江集團橡膠膨脹節http://www.shnxxjjt.com/xjpzj/提供。有疑問請聯系021-60547771

上海淞江減震器集團專業生產銷售橡膠接頭，橡膠軟連接，橡膠柔性接頭，橡膠避震喉,橡膠膨脹節,橡膠補償器等,產品品種齊全,質量穩定,暢銷國內外。

怎么安裝橡膠接頭才能防止開裂？

想要防止橡膠接頭的開裂，我們在平時的使用中就要留意對其進行保護，按照以下的操縱步驟就可以了，我們就會減少斷裂的事件發生。

第一，鏈接部位的強度比較低，那么如果是膠接方法不準確，接頭的強度就會更加低，有可能會出 現開裂.

第二，使用的過程中所鏈接的長度不夠，強行超出鏈接長度，隨意擴大收縮范圍也有可能開裂.

第三，安裝好后，在管道其它地方隨意拉帶此處超出伸縮范圍，也有可能開裂.

第四，在戶外惡劣天氣的影響下，爆曬等，低于使用溫度也有可能開裂。

第五，在制作硫化過程中所用橡膠橡膠機能不好或已經自硫失效、打磨過度、鋼絲繩生銹等，接頭部位的強度將會大打折扣，在使用時，也會有可能輕易泛起接頭部位斷開的現象。

當我們用機械方式橡膠接頭連接時，接頭強度僅能達到帶體強度的百分之四十至百分之五十，冷膠方式質量比較好時，接頭強度能達到百分之六十至百分之七十，而熱膠接頭強度能達到百分之八十至百分之九十，要確保接頭方法準確、無質量缺陷.

所以我們在安裝橡膠接頭的時候要正確安裝。不要強制安裝。

The picture and text provided by the Shanghai Songjiang group shockproof rubber connector http://www.shnxxjjt.com/. Have questions, please contact 021-60547771

Shanghai Songjiang absorber group professional production and sales of rubber joints, rubber soft connection, flexible rubber joint, shock absorber rubber hose, rubber expansion joint, rubber compensator, product variety is complete, stable quality, best-selling domestic.

How to install rubber joints to prevent cracking?

To prevent cracking of rubber joints, we should pay attention to the use of the usual protection, in accordance with the following control steps can be, we will reduce the occurrence of the fault.

First, the strength of the link site is relatively low, so if it is a plastic connection method is not accurate, the strength of the joint will be even lower, there may be cracking.

Second, the use of the process of the length of the link is not enough, forced out of the link length, free to expand the scope of the contract also has the potential to crack.

Third, after installation, in other places free here beyond the extension range of pipe strap, there may be cracking.

Fourth, under the influence of adverse weather conditions, such as the sun, the temperature is also lower than the use of cracking.

Fifth, in making vulcanization process for rubber and its function is not good or have since sulfur failure, polished excessive, wire rope, such as rust, the strength of joints will be greatly reduced, when in use, could easily thrown joints off phenomenon.

When we use mechanical rubber joints, joint strength can only achieved with a 50 percent to 40 percent of the body strength, cold glue quality is good, the strength of the joint can reach 70 percent to 60 per cent, and hot glue joint strength can reach 90 percent ten to eight percent, to ensure the joint method is accurate, no quality defects.

So we need to install the rubber connector correctly. Don't force the installation.