化液無火花切割鋸江蘇宿遷說明”更多信息
產品（FDJ-120型風動切割鋸）介紹：
FDJ-120型乳化液切割鋸，適用于較危險的工作環境，可在較高溫的環境下作業，無火花，在潮濕的環境中無漏電危險，是一款性能可靠、安全型及效率極高的理想風動工具之一。廣泛用于采礦、石化、建筑等行業。
利用井下乳化液系統作為動力源。重量輕，易攜帶；結構科學，便于作業。
可快速切割管道、電纜、角鋼、結構鋼、U型鋼、工字鋼、軌道、鏈條、錨桿、錨索等。
錮金屬鋼合金超級鋸條，耐高溫、耐摩擦、使用壽命長。非常適用于鋸割不銹鋼、鎳基合金、鐵、銅、鋁、玻璃、塑料、木材等。
優點：安全防爆、輕巧便攜、鋸割范圍廣泛。
手持式氣動/乳化液切割鋸常規技術參數：
|
型號
|
功率
|
耗氣量(m3/min)
|
切割厚度
|
切割寬度（直徑）
|
鋸片速度
|
重量
|
|
120
|
0.5kw
|
0.6
|
三種鋸片：
0—30mm
30—50mm
50—120mm
|
120mm
|
60m/min
|
6kg
|
|
180
|
1.0kw
|
1.2
|
180mm
|
90m/min
|
10kg
|
|
230
|
1.5kw
|
1.5
|
230mm
|
120m/min
|
16kg
|
使用方法：
1、了解所需切割的材料。
2、確保牢固固定了所需切割的材料，防止其移動。
3、電源接上時，用手指按壓閥桿，然后開始切割。
4、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命。（注意：避開切割后可能掉落的碎片。切割即將完成時，切勿使鋸碰到您的身體、工件或附近的其它人員。）
5、下次切割開始前，鋸片必須保持運動狀態。電動鋸時，鋸片不能接觸任何表面。
6、更換鋸片前，務必?cái)嚅_電源力。
7、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。
為了安全作業需要注意以下幾點：
1、用鋸的重量來控制切割壓力。對于較軟的材料來說，這樣的重量已經足夠。過多的壓力會降低鋸片的速度。對于較硬的材料，可以通過加壓的方式來降低鋸片的轉動速度。切割是保持鋸筆直。鋸片的任何扭曲或歪斜都可能降低其使用壽命
2、關閉電源時，釋放閥桿。
3、更換鋸片前，務必?cái)嚅_電源。
4、順時針轉動調整手柄以便釋放鋸片導桿上的張力。然后釋放側面板的鎖以便打開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。
5、下次切割開始前，鋸片必須保持運動狀態。電動鋸時，鋸片不能接觸任何表面。
6、了解所需切割的材料。
7、確保牢固固定了所需切割的材料，防止其移動。
8、接電源時，用手指按壓閥桿，然后開始切割。
9、斷開電源時，關閉電源軟管閥。斷開前，先打開電源閥給軟管減壓
聯系人金經理電話13934240041
More about the mining wind cutting saw:
Bolt cutting saw is in mine roadway, the roadway repair, used to trim the length of anchor a supporting tool, it can be safely and quickly cut off the high strength bolt diameter below 24 mm; in addition, it also solves the problem of air inlet area, goaf, goaf, air return area, fast falling roof caving the issue of angle, make the gas and coal dust accumulation amount reduced, preventing the accumulation of gas and coal dust hazard.
Cutting materials and applicable scope: (hand held explosion-proof cutting saw is mainly used for cutting coal mines, high gassy mines, oil pipelines, natural gas pipelines, cables and so on, which requires no sparks in the cutting process).
Iron, steel, copper, iron, copper, cable, anchor, steel mesh, I-beam, channel steel, U steel, H steel, steel, steel, steel, coal miners C steel rail.
FDJ-120 type mine emulsion pipe cutting saw, cable emulsion non spark cutting saw, the emulsion of -120 type coal mine angle cutting saw, mine explosion-proof structure steel cutting saw, FDJ-120 type tunnel U type steel cutting saw, I-beam without spark cutting machine, FDJ-120 type track cutting cutting saw, chain saw, cutting off the coal mine FDJ-120 type mine anchor cable cutting saw, pneumatic hand-held cutting saw no spark...
FDJ-120/180/230 hand-held emulsion / wind cutting saw use method:
1, understand the material needed to cut, if necessary to reduce the speed of rotation of the saw blade by reducing the pressure of the air.
2, ensure that the required cutting material is firmly fixed to prevent its movement.
3. When the emulsion motor is motor, the stem is pressed with the finger and then the cutting is started.
4, use the weight of the saw to control the cutting pressure. This weight is enough for softer materials. Too much pressure can reduce the speed of the saw blade. For harder materials, the speed of rotation of the saw blade can be reduced by pressure. The cutting is to keep the saws straight. Any twist or skew of the sawblade may reduce its service life. (notice: avoid debris that may fall after cutting. When the cutting is about to be finished, do not make the saw touch your body, the workpiece, or the other people in the vicinity.
5. When the air motor is closed, the stem is released.
6. The saw blade must remain moving before the next cutting begins. The saw blade can't contact any surface when a pneumatic saw.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, be sure to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
Shanxi million Zejin Machinery Equipment Manufacturing Co., in 2002 began to engage in the specific work of mining engineering, then according to their own demand, starting their own R & D and production of series of mining machinery needs, and transformation into today, customers all over the country, machinery manufacturing industry leader. It is a factory specializing in mining equipment, the company produces the mine / emulsion pneumatic cutting saw technology mature, the quality is excellent.
