供應YUKEN液壓泵A22-F-R-01-H-K-32 

柱塞泵特點

YUKEN油研柱塞泵具有容積效率高、節能、控制方式多樣、靈活性強等特點，廣泛用于注塑成形機、油壓機、鋼鐵廠、機床、行走機械、液壓電梯和環保工廠等。

產品分類：

YUKEN油研柱塞泵、YUKEN葉片泵、YUKEN電磁閥、YUKEN變量柱塞泵、YUKEN定量葉片泵、YUKEN油缸、YUKEN油泵、YUKEN液壓泵、YUKEN方向閥、YUKEN流量閥、YUKEN壓力閥、YUKEN液壓馬達、YUKEN比例閥。

產品系列

變量柱塞泵A系列軸的對中：盡可能使用柔性連軸器，以免由于彎曲或推力引起的任何應力。不同軸度誤差應小于0.25mm(0.01in)，角度誤差小于0.2?冢?Cbr/>5、變量柱塞泵A系列吸入壓力：允許吸入壓力在-0.16-+0.5bar之間，吸入口配管直徑與所有規定的管道法蘭直徑相同，變量柱塞泵的吸入口高于油箱液面，高度須小于1m。

變量柱塞泵A系列液壓系統噪聲振動的控制：其脈動波形與葉片泵不同，故噪音受主機的剛性、安裝、配管的影響，致使噪聲有增大的可能性，所以安裝變量柱塞泵時需要加以注意。

變量柱塞泵A系列泄油管：安裝時應保證變量柱塞泵腔內壓力保持低于1bar(1kgf/cm2)正常壓力，沖擊壓力小于5bar。配管長應小于1m，管端應浸沒在油中，泄油管單獨接回油箱。

A16-F-R-01-H-K-32,A16-F-R-01-C-K-32,A16-F-R-01-B-K-32,
A22-F-R-01-C-K-32,A22-F-R-01-B-K-32,
A37-F-R-01-H-K-32,A37-F-R-01-C-K-32,A37-F-R-01-B-K-32,
A56-F-R-01-H-K-32,A56-F-R-01-C-K-32,A56-F-R-01-B-K-32,
A220-F-R-01-H-K-10,A220-F-R-01-C-K-10
A16-F-R-01-H-S-K-32,A16-F-R-01-C-S-K-32,A16-F-R-01-B-S-K-32,
A22-F-R-01-C-S-K-32,A22-F-R-01-B-S-K-32,
A37-F-R-01-H-S-K-32,A37-F-R-01-C-S-K-32,A37-F-R-01-B-S-K-32,
A56-F-R-01-H-S-K-32,A56-F-R-01-C-S-K-32,A56-F-R-01-B-S-K-32,
A80-F-R-01-H-S-K-30,A80-F-R-01-C-S-K-30,A80-F-R-01-B-S-K-30,
A125-F-R-01-H-S-K-30,A125-F-R-01-C-S-K-30,A125-F-R-01-B-S-K-30,
A系列變量柱塞泵壓力補償型.
A10-FR01H-12,A10-FR01C-12,A10-FR01B-12,
A70-FR01HS-60,A70-FR01CS-60,A70-FR01BS-60,A70-FR01KS-60,
A90-FR01HS-60,A90-FR01CS-60,A90-FR01BS-60,A90-FR01KS-60,
A145-FR01HS-60,A145-FR01CS-60,A145-FR01BS-60,A145-FR01KS-60,
A10-LR01B-12,A10-LR01C-12,A10-LR01H-12,
A70-LR01BS-60,A70-LR01CS-60,A70-LR01HS-60,A70-LR01KS-60,
A90-LR01BS-60,A90-LR01CS-60,A90-LR01HS-60,A90-LR01KS-60,
A145-LR01BS-60,A145-LR01CS-60,A145-LR01HS-60,A145-LR01KS-60,
A16-L-R-01-B-K-32,A16-L-R-01-C-K-32,A16-L-R-01-H-K-32,
A22-L-R-01-B-K-32,A22-L-R-01-C-K-32,
A37-L-R-01-B-K-32,A37-L-R-01-C-K-32,A37-L-R-01-H-K-32,